128 BUTTERFLY VALVE ROTALY DAMPER DIAPHRAGM CONTROLL VALVE BALL VALVE VALVE ULTRA SONIC VOLTEX FLOWMETER IMPERA FLOWMETER ULTRA SONIC FLOWMETER *1. Calculate the Maximum Frequency of Each Size by the Following Calculation method. Maximam Frequency(Hz) = Maximam Flow Rate(cc/s) / K-Factor(cc/Pulse) Nominal Size Socket End Flanged End PVC/HI-PVC C-PVC L H JIS10K JIS5K mm inch L H D L H D D d t n e D d t n e 15 1/2 164 119 57 150 119 56 500 119 95 70 14 4 15 80 60 9 4 12 20 3/4 164 121 57 150 121 56 500 121 100 75 15 4 15 85 65 10 4 12 25 1 164 121 57 150 121 56 500 121 125 90 15 4 19 95 75 10 4 12 32 11/4 164 122 57 150 122 56 500 122 135 100 16 4 19 115 90 12 4 15 40 11/2 164 125 57 150 125 56 500 125 140 105 16 4 19 120 95 12 4 15 50 2 180 128 70 164 128 69 500 128 155 120 20 4 19 130 105 14 4 15 65 21/2 190 133 87 190 133 87 500 133 175 140 22 4 19 155 130 14 4 15 80 3 200 136 102 200 136 102 500 136 185 150 22 8 19 180 145 14 4 19 100 4 250 168 130 250 168 130 700 168 210 175 22 8 19 200 165 16 8 19 125 5 322 176 157 − − − 700 176 250 210 24 8 23 235 200 16 8 19 150 6 390 182 186 − − − 700 182 280 240 26 8 23 265 230 18 8 19 *1. Piping Condition: Straight pipe of at least ten times the diameter upstream of the meter, and five diameters down stream are strongly recommended. Wiring Condition: Use the Shield line when you extend wiring. *2. When flowing quantity is displayed, the Special Indicator is needed. *3. Some externals and the shape of the Flow meter are different according to the diameter. ●Flanged End Inpella Flow Meter ASIP80 Series ■ The ASIP80 Series is a Flow Meter of the Insertion Type that uses a Special Fitting. ■ No Corrosion (All Plastic) FEATURES SPECIFICATIONS Model ASIP81(P/Y/K) ASIP82(P/Y/K) Nominal Size 15mm(1/2")-80mm(3") 100mm(4")-150mm(6") Type of Connection Socket, Flange Material Body Working Temperature℃ (°F) HI-PVC:　50℃（120°F） PP　　:　60℃（140°F） PVDF　:　90℃（194°F） Max. Working Pressure(at r.t.) MPa{kgf/cm2}[PSI] 1.0MPa (10.2kgf/cm2）[150] Inpella PVDF Shaft Zirconium, Silicon-Carbide Bearing Ruby O-ring FKM (EPDM) Special Fitting PVC, HI-PVC, C-PVC Measurement fl uid Fluid (High viscosity fl uid and slurry is excluded.) Max. Working Temperature 0-90℃（32-194°F） Flowrate 0.2-9 m/s Range Ability 1 : 45 Measurement accuracy ± 1.5% (FS) Power Source DC6V-24V (Current Consumption: 8mA) Output Signal Current Sinking Pulse (NPN) 20mA maximum Cable 3-con (3.6m) Fitting Installation Straight pipe of at least ten times the diameter upstream of the meter, and five diameters down stream are strongly recommended. Temperature (℃) Pressure MPa(kgf/cm2)[PSI] PVC, HI-PVC C-PVC 15mm-150mm (1/2"-6") 15mm-50mm (1/2"-2") 65mm-150mm (2 1/2"-6") 20 1.0(10.2)[150] 1.0(10.2)[150] 1.0(10.2)[150] 30 0.9(9.8)[130] 1.0(10.2)[150] 0.8(8.2)[115] 40 0.7(7.1)[100] 1.0(10.2)[150] 0.8(8.2)[115] 50 0.3(3.1)[45] 0.6(6.1)[90] 0.6(6.1)[90] 60 − 0.6(6.1)[90] 0.6(6.1)[90] 70 − 0.4(4.1)[60] 0.4(4.1)[60] 80 − 0.2(2.0)[30] 0.2(2.0)[30] 90 − 0.2(2.9)[30] 0.2(2.9)[30] Nominal Size Flow Rate(m3/h) K-Factor mm inch Min - Max (cc/Pulse) 15 1/2 0.14 - 6.51 7.1 20 3/4 0.23 - 10.18 10.9 25 1 0.35 - 15.89 16.1 32 1 1/4 0.54 - 24.44 26.8 40 1 1/2 0.90 - 40.69 47.2 50 2 1.47 - 66.16 66.2 65 2 1/2 2.54 - 114.17 102.2 80 3 3.35 - 150.80 139.7 100 4 5.65 - 254.34 213.0 125 5 8.83 - 397.40 355.4 150 6 12.05 - 542.15 465.0 Figure. 1 Max.Working Pressure and Working Temprerature of Special Fitting. Figure. 2 Flow Rate and K-Factor DIMENSIONS TABLE Unit:mm