160 HIGH PURITY SERIES HP-PVC PIPE & FITTINGS ●Elbow(L) Unit:mm Nominal Size (mm) D t H 13 24 3.0 36 16 29 3.5 43 20 33 3.5 50 25 40 4.0 58 30 46 4.0 65 40 57 4.5 82 50 70 5.0 96 ※ 65 87 6.6 110 ※ 75 102 8.0 120 ※ 100 130 10.0 153 ※ 125 157 11.0 188 ※ 150 186 13.0 230 □ 200 240 15.0 265 □ 250 295 16.0 310 300 347 18.0 350 （Note） 1.The tolerances on H are +5/-1mm. 2.The Nominal Size marked with ※ conform to the JPPFA standard. 3.The Nominal Size marked with □ conform to the AV standard. ●HP-PVC Pipe Unit:mm Nominal Size (mm) D t d L Outer diameter Wall Thickness Approximate I.D. (for reference) Basic Length Dimension (mm) Maximum and Minimum tolerances Average tolerances Minimum Tolerance 13 18 ±0.2 ±0.2 2.2 ＋0.6 13 4,000±10 16 22 ±0.2 ±0.2 2.7 ＋0.6 16 4,000±10 20 26 ±0.2 ±0.2 2.7 ＋0.6 20 4,000±10 25 32 ±0.2 ±0.2 3.1 ＋0.8 25 4,000±10 30 38 ±0.3 ±0.2 3.1 ＋0.8 31 4,000±10 40 48 ±0.3 ±0.2 3.0 ＋0.8 40 4,000±10 50 60 ±0.4 ±0.2 4.1 ＋0.8 51 4,000±10 65 76 ±0.5 ±0.3 4.1 ＋0.8 67 4,000±10 75 89 ±0.5 ±0.3 5.5 ＋0.8 77 4,000±10 100 114 ±0.6 ±0.4 6.6 ＋1.0 100 4,000±10 125 140 ±0.8 ±0.5 7.0 ＋1.0 125 4,000±10 150 165 ±1.0 ±0.5 8.9 ＋1.4 146 4,000±10 200 216 ±1.3 ±0.7 10.3 ＋1.4 194 4,000±10 250 267 ±1.6 ±0.9 12.7 ＋1.8 240 4,000±10 300 318 ±1.9 ±1.0 15.1 ±2.2 286 4,000±10 （Note） 1.The tolerances of lengths are ± 10mm. 2. The maximum and minimum tolerances on outside diameters are the tolerances on O.D. measurements taken at randomly selected spots. 3. The average tolerances on outside diameters are the tolerances on the arithmetical mean of O.D. measurements taken at randomly selected spots in two directions at a right angle to each other. HP-PVC Pipe ●Dimensions Commom All of AV TS Socket. JIS K6743 Unit:mm Nominal Size (mm) d1 Tolerance on d1 d2 . 1/T D DT Tolerance on D&DT d (minimum value) Pipe O.D. 13 18.40 ±0.20 − 26 1/30 24 24.0 −0.6 13 18 16 22.40 ±0.20 − 30 1/34 29 29.0 −0.7 16 22 20 26.45 ±0.20 − 35 1/34 33 33.0 −0.8 20 26 25 32.55 ±0.25 − 40 1/34 40 40.0 −1.0 25 32 30 38.60 ±0.25 − 44 1/34 46 46.0 −1.0 31 38 40 48.70 ±0.30 − 55 1/37 57 57.0 −1.2 40 48 50 60.80 ±0.30 − 63 1/37 70 70.0 −1.5 51 60 ※ 65 76.60 ±0.30 − 61 1/48 87 88.5 −1.5 67 76 75 89.60 ±0.30 − 64 1/49 102 104.5 −1.5 77 89 100 114.70 ±0.30 − 84 1/56 130 133.5 −1.8 100 114 ※125 140.85 ±0.35 − 104 1/58 157 161.0 −1.8 125 140 150 166.00 ±0.40 − 132 1/63 186 190.0 −2.0 146 165 ※200 217.00 − 214.10 145 − 240 − − 194 216 ※250 268.20 − 265.00 155 − 295 − − 247 267 ※300 319.6 − 315.50 175 − 347 − − 298 318 （Note） 1.The tolerances on l are +4/-0.5mm. 2.The Nominal Size marked with ※ conform to the AV standard and the JPPFA standard. Fittings in size 200, 250mm are available on request by FRP reinforcement. Max working pressure 200mm : 1.0MPa{10.2kgf/cm2} at 20℃ 250mm : 1.0MPa{10.2kgf/cm2} at 20℃ . . Taper 1/Ｔ φd1 φd φD φd1 φD φDT φd2 φd H D H t H H D t ▼13mm - 50mm ▼65mm - 300mm t L φd φD ▼13mm - 150mm ▼200mm - 300mm Working Pressure with Temperature Temp. Nom. Size 20℃ 30℃ 40℃ 50℃ 13mm - 300mm 1.0｛10.2｝ 0.9｛9.2｝ 0.7｛7.1｝ 0.3｛3.1｝ MPa｛kgf/cm2｝ Note:This data is applicable for ultrapure water. Working Pressure with Temperature Temp. Nom. Size 20℃ 30℃ 40℃ 50℃ 13mm - 150mm 1.0｛10.2｝0.9｛9.2｝ 0.7｛7.1｝ 0.3｛ 3.1｝ 200mm 0.75｛7.7｝ 0.6｛6.1｝ 0.5｛5.1｝ 0.25｛2.6｝ 250mm 0.6｛6.1｝ 0.5｛5.1｝ 0.4｛4.1｝ 0.2｛2.0｝ 300mm Elbow, Reducing Socket, Socket 0.6｛6.1｝ 0.5｛5.1｝ 0.4｛4.1｝ 0.2｛2.1｝ 300mm Other Fitting 0.4｛4.1｝ 0.4｛4.1｝ 0.3｛3.1｝ 0.1｛1.1｝ MPa｛kgf/cm2｝ Note:This data is applicable for ultrapure water. Dimensions Common All of AV TS Socket. JIS K6743 Elbow(L) TRUE UNION DIAPHRAGM LAB COCK PANEL MOUNTING BALL VALVE TYPE21 VALVE TYPE14 HP-PVC PIPES AV GASKET MULTI-JOINT AV FLANGE AV PREFAB JOINT HP-PVC FITTINGS & FITTINGS