016 Unplasticized Polyvinyl Chloride Pipe Fitting | TS・HITS Fitting T Type N Field ＊ Material ＊＊ Model J Standard ＊＊＊ Size 9L 90° Elbow 4L 45° Elbow SO Socket TE Tee FL Faucet Elbow (Metal not contained) KL Faucet Elbow (Metal contained) FT Faucet Tee (Metal not contained) KT Faucet Tee (Metal not contained) FS Faucet Socket (Metal not contained) KS Faucet Socket (Metal contained) VS Valve Socket (Metal not contained) US Union Socket CP Cap N Type U U-PVC J JIS N Standard I HI-PVC T TS Fitting N Standard 010 10�o . 150 150�o 016013 16×13�o . 150125 150×125�o PRODUCT MODEL CODE LIST φD φd1 Taper 1/T DT φd φd φD Taper 1/T φd1 DT Socket Common Dimensions Size 13 − 50 mm Socket Common Dimensions Size 65 − 150 mm R R φD φd1 Taper 1/T DT φd φd φD Taper 1/T φd1 DT Socket Common Dimensions Size 13 − 50 mm Socket Common Dimensions Size 65 − 150 mm R R TS・HITS Fitting Common Dimensions JISK6743 TS...Unplasticized Polyvinyl Chloride Pipe Fitting HITS... Impact-Resistant Unplasticized Polyvinyl Chloride Pipe Fitting Size d1 d1 Tolerance R 1/T D DT D and DT Tolerance d (Min.) Applicable Pipe Outer Diameter □ 10 15.40 ±0.20 22.0 1/25 21.0 21.0 .0.5 10 15 13 18.40 ±0.20 26.0 1/30 24.0 24.0 .0.6 13 18 16 22.40 ±0.20 30.0 1/34 29.0 29.0 .0.7 16 22 20 26.45 ±0.20 35.0 1/34 33.0 33.0 .0.8 20 26 25 32.55 ±0.25 40.0 1/34 40.0 40.0 .1.0 25 32 30 38.60 ±0.25 44.0 1/34 46.0 46.0 .1.0 31 38 40 48.70 ±0.30 55.0 1/37 57.0 57.0 .1.2 40 48 50 60.80 ±0.30 63.0 1/37 70.0 70.0 .1.5 51 60 ● 65 76.60 ±0.30 61.0 1/48 87.0 88.5 .1.5 67 76 75 89.60 ±0.30 64.0 1/49 102.0 104.5 .1.5 77 89 100 114.70 ±0.30 84.0 1/56 130.0 133.5 .1.8 100 114 ●125 140.85 ±0.35 104.0 1/58 157.0 161.0 .1.8 125 140 150 166.00 ±0.40 132.0 1/63 186.0 190.0 .2.0 146 165 Notes: 1. R tolerance shall be +4 -0.5 mm. 2. D and DT tolerance and t tolerance on the plus side are not restricted. 3. □ conform to the AV standard. 4. ● conform to the JPPFA standard. ■ Dimensions Table (Unit: mm)