○ × × ○ ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × Packed products sealed condition ○ × × × ○ ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition ○ × × × ○ ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition ○ × ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less ○ × × × ○ ○ End Stopper Panel 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition Piping Design Precautions Transportation Precautions Storage Precautions .Select an appropriate material in consideration of use conditions (fluid type, temperature, pressure, etc.) For details, please consult our nearest office in advance. .Maximum working pressure is the pressure including the water hammer pressure. Do not use them exceeding the maximum working pressure. .As maximum working pressure differs by size and temperature, design and use within the allowable range. .Since they are made from plastic, heat expansion/contraction against temperature change is large compared to metals and heat stress is also generated. Therefore, perform piping support or expansion/construction treatment applicable to the use conditions and installation place. .In the case of using under the positive-pressure gas, a dangerous condition is expected due to the particular reaction force of compressive fluid even when the the value is the same as the water pressure. Therefore, implement a safety measure such as covering pipes with a protection material, etc. to protect the surrounding area before use. .Do not joint with solvent adhesive or welding connection on differential plastic materials (It may cause damage) .Do not drag them as it could scratch pipes. Do not drag them as both ends of pipes are easily damaged. .Two people should handle a pipe with the size of 150 mm or more. .Do not throw pipes from the truck platform. .When storing pipes and fittings outside, avoid direct sunlight and implement a measure such as placing a sheet in a way of avoiding heat accumulation. .Do not leave fittings in an enclosed condition (inside a vehicle in summer, in an enclosed plastic bag, etc.) under a high temperature atmosphere. ○ × × × ○ ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition ○ × × × ○ ○ End Stopper Panel Approximately 1.5 m or less 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition Installation .Follow our installation procedure to fully exert the work safety and piping performance for installation. .Make sure to use the specified AV cement for bonding AV PVC pipes. .Be cautious of excessive adhesive (it may cause solvent cracking and damage). Caution is needed in low-temperature installation because solvent steam does not evaporate easily and tends to remain (it may cause solvent cracking and damage). During curing after piping, open both ends of pipe without enclosing and remove the solvent steam. During curing, it can be removed more effectively by ventilating inside piping using a ventilator (low-pressure specification) or washing inside piping by filling the water fully after the adhesive is hardened. .Make sure to perform a completion inspection under water pressure. Do not perform an airtightness test by using air (compressed air or positive-pressure gas) as it is extremely dangerous. ○ × × × ○ ○ End Stopper Panel 1 m or less 1 m or less 1 m or less 1 m or less Enclosed vehicle (may deform due to heat) × × Packed products in a sealed condition 063 To use piping materials (PVC Pipe & Fittings) safety