015 HANDLE ROTATION [FULL OPEN (ROTATION/LIFT) FULL CLOSE] MANUAL COMPATIBLE ACTUATOR AUTOMATIC SIZE ROTATION 15mm ( 1/2inch) 3.3 20mm ( 3/4inch) 3.3 25mm ( 1inch) 4.0 32mm (1 1/4inch) 4.0 40mm (1 1/2inch) 5.0 SIZE ROTATION 50mm ( 2inch) 6.0 65mm (2 1/2inch) 9.0 80mm ( 3inch) 10.0 100mm ( 4inch) 10.0 DIAPHRAGM VALVE TYPE 14 DIAPHRAGM VALVE / DIAPHRAGM VALVE TYPE 14 . NEAR-LINEAR FLOW CHARACTERISTICS . A NEW TYPE OF RUBBER HAVING A HIGH RELIABILITY IN LEAKAGE PREVENTION IS USED FOR THE DIAPHRAGM AND CUSHION. . THE ORIGINAL DESIGN ACHIEVES HIGH SEALING PERFORMANCE WITH LOW TORQUE. . BAYONET STRUCTURE ALLOWING QUICK DIAPHRAGM REPLACEMENT . EQUIPPED WITH A BOTTOM STAND ALLOWING EASY AND SECURE REPLACEMENT (See P. 69 for details.) BASIC SPECIFICATIONS VALVE TYPE―――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――DIAPHRAGM VALVE TYPE 14 SIZE―――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――15 mm−100 mm (1/2 inch−4 inch) BODY MATERIAL―――――――――――――――――――――――――――――――――――――――――――――――――― U-PVC C-PVC PP PVDF SEAL MATERIAL / DIAPHRAGM―――――――――― EPDM PTFE FKM etc. CONNECTION / FLANGED――――――――――――――――――――――――――――――――JIS10K, DIN PN10, ANSI CLASS150 HIGH PURITY SERIES―――――――――――――――――――――――――――LUBRICANT FREE FLUID TEMPERATURE MAXIMUM WORKING PRESSURE (NORMAL TEMPERATURE) MPa{kgf/cm2} CONNECTION METHOD FLANGED U-PVC 0℃ 〜 60℃ 1.0｛10.2｝ ○ C-PVC 0℃ 〜 90℃ 1.0｛10.2｝ ○ PP - 20℃ 〜 90℃ 1.0｛10.2｝ ○ PVDF - 40℃ 〜 120℃ 1.0｛10.2｝ ○ NOTE The maximum working pressure is the value including the water hammer pressure. Be careful that the maximum working pressure is not exceeded during use. * Concerning the allowable pressure for each temperature and material, see the technical documents at the end of this catalog. * The diaphragm may become loose due to temperature changes during long storage, operation stop or while in use. Check the conditions and then retighten the bolts and nuts between the bonnet and the body to the "bonnet tightening torque". (Failure to do so may cause fluid leakage.) AUTOMATIC MANUAL PARTS LIST MANUAL ● WHEN DIAPHRAGM MATERIAL IS PTFE 20 21 20 8a 11 10 88 2 18 1 12 13 14 16 15 8 9 17 6 7 3 3 4 3a 13 12 15 17 89 94 90 1a 14 16 8 9 6 3a 3 11 10 2 18 1 PART NO. / NAME QTY MATERIAL 17 THRUST RING (B) 1 UHMWPE 18 BOLT/NUT (A) 4 SUS304 20 STOPPER 1 C3604(3), SUS304(4) 21 SCREW(3) 1 SUS304 88 GREASE NIPPLE(4) 1 C3604 89 COMPRESSOR PIN(4) 1 SUS304 90 STUD BOLT/NUT(4) 4 SUS304 94 COMPRESSOR 1 SUS304 1a STUD NUT(4) 4 C3604(5), SUS304(6) PART NO. / NAME QTY MATERIAL 8 STEM 1 C3604 8a DISPLAY LOT(4) 1 SUS304 9 SLEEVE 1 C3604 10 HANDLE 1 PP 11 GAUGE COVER 1 PC 12 NAMEPLATE 1 U-PVC 13 C-SHAPED STOP RING 1 SUS304 14 O-RING (A) 1 EPDM 15 O-RING (B) 1 EPDM 16 THRUST RING (A) 1 UHMWPE PART NO. / NAME QTY MATERIAL 1 BODY 1 BODY――――――――――――BONNET U-PVC―――――――――――U-PVC C-PVC――――――――――PP PP―――――――――――――――――――PP PVDF―――――――――――――PPG(1) PVDF―――――――――――――PVDF 2 BONNET 1 3 DIAPHRAGM 1 EPDM, PTFE, etc. 3a EMBEDDED DIAPHRAGM FITTING 1 SUS304 4 CUSHION(2) 1 EPDM 6 COMPRESSOR 1 PVDF 7 JOINT FITTING(3) 1 SUS304 NOTE (1) Bonnet PPG 15 . 100 mm: black. 125 . 250 mm: ivory. (2) is used when the diaphragm material is PTFE. (3) is used for sizes of 50 mm or less. (4) is used for sizes of 65 mm or more. (5) is used when the body material is U-PVC, C-PVC or PP. (6) is used when the body material is PVDF. PNEUMATIC TYPE AN For detailed specifications, see P.117 PNEUMATIC TYPE AV For detailed specifications, see P.118 PNEUMATIC TYPE AP For detailed specifications, see P.122 ELECTRIC TYPE H For detailed specifications, see P.126 ELECTRIC TYPE M For detailed specifications, see P.127