173 PARTS LIST MANUAL 32 mm . 150mm (1. inch . 6 inch) DETAIL OF EMBEDDED BODY FITTING THREADED 200 mm . 350 mm (8 inch . 14 inch) (Top) (Bottom) 125mm, 150mm 29 28 22 23 7 26 27 25 24 21 6 9 5 8 2c 26 27 25 14 17 16 9 15 10 8 2c 1a 29 28 22 23 24 5 11 6 4 7 3 1 4 3 1 MANUAL WATER/WASTEWATER- AND AGRICULTURE-RELATED / GATE VALVE STANDARD TYPE (TYPE P) INSIDE SCREW ROUND HANDLE TYPE GATE VALVE STANDARD TYPE (TYPE P) INSIDE SCREW ROUND HANDLE TYPE . EQUIPPED WITH OPENING INDICATOR UNDER THE HANDLE TO ALLOW FOR EASY CHECK OF OPENING DEGREE OF THE VALVE. . FOR ALL THE WETTED PARTS, CORROSION-RESISTANT MATERIAL IS USED. . MADE OF ROBUST, LIGHTWEIGHT AND IMPACT-RESISTANT HARD VINYL CHLORIDE (HI-PVC), WITH A WEIGHT OF 1/3 TO 1/5 COMPARED TO METAL VALVES. NOTES (1) For the round handle type, directly hold the round handle when opening or closing the valve. If a turning bar or similar tool is used to open or close the valve, the handle will be broken. (2) Concerning the flanged type compatible with the waterworks and JIS10K standards, the products of sizes of 40 to 150 mm are registered as valves certified by the Quality Certification Center, Japan Water Works Association. BASIC SPECIFICATIONS VALVE TYPE――――――――――――――― GATE VALVE STANDARD TYPE (TYPE P) 　　　　　　　　　　　　　INSIDE SCREW ROUND HANDLE TYPE SIZE―――――――――――――――――――――― 32 mm−350 mm (1 1/4 inch−14 inch) BODY MATERIAL―――――――――― HI-PVC SEAL MATERIAL / O-RING―――― EPDM etc. CONNECTION / FLANGED―――― JIS5K, JIS10K, DIN, ANSI 　　　　　 THREADED――― Rc, Rp, NPT FLUID TEMPERATURE MAXIMUM WORKING PRESSURE (NORMAL TEMPERATURE) MPa{kgf/cm2} CONNECTION METHOD 32mm―200mm 250mm 300 mm・350 mm FLANGED THREADED HI-PVC -10℃ 〜 50℃ 1.0｛10.2｝ 0.75｛7.7｝ 0.5｛5.1｝ ○ ○ NOTES The maximum working pressure is the value including the water hammer pressure. Be careful that the maximum working pressure is not exceeded during use. * Concerning the allowable pressure for each temperature and material, see the technical documents at the end of this catalog. PART NO. / NAME QTY MATERIAL 1 BODY 1 HI-PVC 1a EMBEDDED BODY FITTING (1) ーC3604 2c GATE (BODY) (A) 1 PP 3 STEM 1 U-PVC 4 BONNET (LID) (A) 1 HI-PVC 5 BONNET (LID) (B) 1 HI-PVC 6 THRUST RING 2) 1 SET PP 6a THRUST BEARING(1) 1 SET SUJ2 7 BOLT/NUT ーSUS304 PART NO. / NAME QTY MATERIAL 8 O-RING (B) 1 EPDM, etc. 9 O-RING (C)(3) 2・3 EPDM, etc. 10 BUSH (A)(1) 1 PP 11 BUSH (B)(1) 1 PP 14 O-RING (E)(1) 1 EPDM, etc. 15 O-RING (F)(1) 1 EPDM, etc. 16 O-RING (D)(1) 1 EPDM, etc. 17 SET SCREW (A)(1) 1 SUS304 21 PACKING 1 EPDM PART NO. / NAME QTY MATERIAL 22 HANDLE 1 PP 23 OPENING COVER 1 PC 24 OPENING RING 1 U-PVC 25 GUIDE PIN 1 SUS304 26 GUIDE PIN SUPPORT PLATE 1 U-PVC 27 O-RING (G) 1 EPDM 28 WASHER 1 U-PVC 29 UNION NUT 1 SUS304 NOTES (1) is used for sizes of 200 mm or more (2) is used for sizes of 150 mm or less. (3) The quantity of use is 2 pieces for 150 mm or less and 3 pieces for 200 mm or more. * The parts list above is applicable when the stem is made of U-PVC.