181 PARTS LIST MANUAL * 65 mm has a full-bore structure. * φd' is 125 mm only. 150 mm Conventional type: 65 mm, 125 mm 32 mm . 150 mm (1. inch . 6 inch) 200 mm . 250 mm (8 inch . 10 inch) 34 1 2b 22 6 33 18b 9 8 2d 2c 2b 2k 2j 2c 34 22 6 4 16 5 2e 1a 2g 2f 2b 2c 7 8 33 9 35 3 2d 18b 18a 2g 1 32 4 7 3 5 32 MANUAL WATER/WASTEWATER- AND AGRICULTURE-RELATED / GATE VALVE SOFT SEAL TYPE (TYPE S) OUTSIDE SCREW ROUND HANDLE TYPE GATE VALVE SOFT SEAL TYPE (TYPE S) OUTSIDE SCREW ROUND HANDLE TYPE . MADE OF ROBUST, LIGHTWEIGHT AND IMPACT-RESISTANT HARD VINYL CHLORIDE (HI-PVC). . THE CHANNEL SURFACE FREE FROM IRREGULARITIES ALLOWS FOR SMOOTH FLOW. THE RUBBER SOFT SEAL ENSURES EXCELLENT WATER TIGHTNESS. . THE STEM SCREW IS NOT EXPOSED TO THE FLUID, NO FOREIGN OBJECT DOES NOT ENTER. BASIC SPECIFICATIONS VALVE TYPE――――――――――――――― GATE VALVE SOFT SEAL TYPE (TYPE S) 　　　　　　　　　　　　　OUTSIDE SCREW ROUND HANDLE TYPE SIZE―――――――――――――――――――――― 32 mm−250 mm (1 1/4 inch−10 inch) BODY MATERIAL―――――――――― HI-PVC SEAL MATERIAL / SEAT――――― SBR NBR 　　　　　 O-RING――― EPDM CONNECTION / FLANGED―――― JIS10K, DIN, ANSI FLUID TEMPERATURE MAXIMUM WORKING PRESSURE (NORMAL TEMPERATURE) MPa{kgf/cm2} CONNECTION METHOD 32mm―200mm 250mm FLANGED HI-PVC -10℃ 〜 50℃ 1.0｛10.2｝ 0.75｛7.7｝ ○ NOTES The maximum working pressure is the value including the water hammer pressure. Be careful that the maximum working pressure is not exceeded during use. * Concerning the allowable pressure for each temperature and material, see the technical documents at the end of this catalog. NOTES For the round handle type, directly hold the round handle when opening or closing the valve. If a turning bar or similar tool is used to open or close the valve, the handle will be broken. PART NO. / NAME QTY MATERIAL 1 BODY 1 HI-PVC 1a EMBEDDED BODY FITTING (1) 4 C3604 2b SEAT 1 SBR, NBR 2c GATE (BODY) (A) 1 HI-PVC, C-PVC 2d GATE (BODY) EMBEDDED FITTING (A) 1 BC6 2e GATE (BODY) (B)(1) 1 HI-PVC 2f GATE (BODY) EMBEDDED FITTING (B) (1) 4 C3604 2g BOLT (A) (1) 4 SUS304 2j INTERNAL THREAD DEFLECTOR(2) 4 BC6 PART NO. / NAME QTY MATERIAL 2k DEFLECTOR RETAINER(2) 1 HI-PVC 3 STEM 1 SUS304 4 BONNET (LID) (A) 1 HI-PVC 5 BONNET (LID) (B) 1 HI-PVC, PP 6 THRUST RING (A) 2 PP 7 BOLT/NUT ーSUS304 8 O-RING (B) 1 EPDM, NBR 9 O-RING (C) 2・1 EPDM, NBR 16 O-RING (D)(1) 2 EPDM, NBR PART NO. / NAME QTY MATERIAL 18a DUST SEAL (A) 1 EPDM, NBR 18b DUST SEAL (B) 1 NBR 22 HANDLE 1 PP 32 PIN (A) 1 SUS304 33 SLEEVE 1 C3604, BC6 34 NUT 1 C3604, BC6 35 EMBEDDED LID FITTING(1) 4 C3604 NOTES (1) is used only for 200 mm and 250 mm. (2) is used for sizes other than 65 mm, 125 mm, 200 mm and 250 mm.